How to compare T18 and T35, sheet thickness and the cost of fleece?

T18 and T35 describe different profile heights, but they are not enough to select a covering. You need to check the drawing, steel thickness, supports and the intended use of the sheet. The price also depends on the coating and the coverage. Fleece can help limit condensation dripping, but it needs to dry out. It does not replace insulation or a tight roof. The profile affects stiffness and how the sheet performs. A taller trapezoidal profile may offer different possibilities under the same material conditions. However, this does not mean that every T35 is automatically suitable for any support spacing. Data for the specific product and loads are required.

By |2026-11-14T13:13:34+01:002022-06-23|Building academy|Comments Off on How to compare T18 and T35, sheet thickness and the cost of fleece?

How an eaves flashing directs rainwater into the gutter

The drip edge above the gutter is a flashing at the lower edge of the roof slope that helps direct water from the eaves into the gutter and protects the eaves zone. To assess its performance, trace the path of a droplet from higher up the slope to the outlet and check that each lap carries water onward rather than under the previous layer. Shape and position must suit the covering, membrane and ventilation. Simply sliding metal under the first sheet may not suffice, so the detail is matched to the roof layout.

By |2026-11-15T00:24:10+01:002022-06-23|Building academy|Comments Off on How an eaves flashing directs rainwater into the gutter

What is a panel with glass-fibre reinforced facing?

Some roof panels have a thin composite facing in place of the inner steel sheet. One example is glass-fibre-reinforced polyester resin, used in agricultural buildings. When choosing a panel, check the temperatures, moisture levels and cleaning agents it can withstand, as well as the joint details. The outer facing may be profiled steel. A rigid PUR or PIR foam core sits between this facing and the flat, glass-fibre-reinforced plastic surface facing the room. Together the layers form a sandwich panel. This construction differs from a simple translucent corrugated sheet.

By |2026-11-14T13:11:11+01:002022-06-22|Building academy|Comments Off on What is a panel with glass-fibre reinforced facing?

Tile-effect steel or concrete roof tiles for your home?

When deciding between metal roofing tiles and concrete tiles, start by assessing the structure and shape of the roof slopes, and only then compare appearance, the cost of the complete covering and ease of later repairs. The two materials differ in weight, element format and how details are finished. Metal roofing tiles are lightweight, which can be an advantage in a renovation when the truss has little load-bearing reserve. Looking at the roof is not enough – an inspection is necessary, checking cross-sections, connections and the condition of the timber. A heavier covering must be taken into account in the design of the entire load-bearing system.

By |2026-11-14T20:36:25+01:002022-06-17|Building academy|Comments Off on Tile-effect steel or concrete roof tiles for your home?

What zinc, magnesium and aluminium do in a metallic coating

Before comparing sheets, establish whether the metallic protection is meant to be visible or hidden beneath an organic coating — this affects how the product should be assessed. In a typical roof sheet, the zinc, aluminium and magnesium layer sits on the steel core, under successive finishing layers, though it may also form an uncoated surface. Check the exact coating designation, how its quantity is stated, and whether the data refer to one side or both combined. On a metal-tile sample you usually see the outer layer, not the steel's metallic protection itself.

By |2026-11-15T04:21:32+01:002022-06-17|Building academy|Comments Off on What zinc, magnesium and aluminium do in a metallic coating

Why does a metre of roof panel cost differently from a metre of wall panel?

Roof and wall perform under different conditions. They have different profiles, connections and loads. That is why their prices per metre should not be compared without describing the variant. Even an identical core and thickness do not make an identical product. A reliable quote separates panels, accessories and installation. It also lets you check what you are paying for in each part of the building. A roof panel must work with the slope and drainage system. Its outer skin usually has a pronounced trapezoidal profile. A wall panel may have a flat or lightly profiled surface. Connections are designed for a specific layout and fixing method.

By |2026-11-14T13:14:05+01:002022-06-13|Building academy|Comments Off on Why does a metre of roof panel cost differently from a metre of wall panel?

Damp at a metal roof ridge: leaking ridge caps or a ventilation problem?

A stain below the ridge does not yet indicate the point where water entered the roof. Precipitation may have penetrated through a poorly executed joint. Moisture can also form beneath the covering as condensation. Ridge tiles must be assessed together with the roof slope layers. Only then is it clear whether the flashing needs repair or the ventilation detail needs changing. Simply adding sealant is often a seemingly simple solution. However, it can block the airflow path. Note whether the damp patches occur after rain, during a thaw, or also on dry days. Information on wind direction is helpful. A leak visible only during rainfall from one side suggests a different point to check than drops appearing in the morning under a large part of the roof slope. These are pointers for inspection, not a ready diagnosis.

By |2026-11-15T04:22:08+01:002022-05-19|Building academy|Comments Off on Damp at a metal roof ridge: leaking ridge caps or a ventilation problem?

What belongs beneath the roof covering? Support, drainage and ventilation

A roof substrate is not a single element but a set of layers with different jobs. Battens and boarding carry the loads, while a membrane or other underlay directs water away; counter-battens create a ventilation gap. The choice depends on the roof and covering type – no universal arrangement suits every metal sheet. Before comparing offers, establish what each item includes, as the term may refer to the batten grid, full boarding or just the membrane. Leave the layout decision to the designer.

By |2026-11-15T00:24:26+01:002022-05-13|Building academy|Comments Off on What belongs beneath the roof covering? Support, drainage and ventilation

Choosing a roofer for the whole job, from covering to details

First, check how the roofer intends to resolve the specific roof details, not just the price per square metre. During the conversation, ask for a description of the substrate preparation, the fixing method for the covering and the sequence of work that will later be covered up. Note whether the contractor clearly separates material supply from labour and how they document any changes after uncovering the layers. Photos of valleys, eaves and chimneys give good insight, not only a view of the finished slope. On this basis it is easier to judge whether the offer matches the real conditions of your roof.

By |2026-11-15T04:20:51+01:002022-05-07|Building academy|Comments Off on Choosing a roofer for the whole job, from covering to details

Where roof battens are needed and what they support

In Poland, roof battens serve as supports for the covering and transfer its loads to the roof structure. Readers should first check whether their dimensions and spacing match the specific metal roofing tile system, rather than merely following a crew's habitual practice. The starting detail at the eaves is often key, since the first batten frequently needs a different position from subsequent ones. It is also worth establishing how the air inlet and outlet are resolved, because adding timber alone does not guarantee ventilation. Design decisions remain with the designer.

By |2026-11-14T17:10:05+01:002022-05-05|Building academy|Comments Off on Where roof battens are needed and what they support
Back to top