About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

How do you cut an insulated panel and keep a good edge?

A good cut does not end with achieving the right length. The condition of the coating, the bond between the facings and the core, and the geometry of the edge must be preserved. Support and the removal of swarf matter. Hot cutting can damage the panel. The working method should correspond to the documentation for the specific product and the type of core. Shortening a full element differs from cutting an opening for a service. A large opening can change how the panel performs and may require framing. A narrow strip at the edge should also not be treated as a full panel. Before you make the cut, check its place in the design and the supports required.

By |2026-11-14T10:56:23+01:002022-04-24|Building academy|Comments Off on How do you cut an insulated panel and keep a good edge?

Are thicker metal fence pickets always stiffer?

In an offer, it is easy to find one number and take it as a measure of quality. For fence pickets, this is often the sheet thickness. The parameter matters, but it does not describe the whole product. Metal fence pickets work as formed elements connected to the structure. Their behaviour depends on several features at once. It is worth knowing them before you reject a light profile or buy a heavier one solely on the basis of advertising. Greater thickness can improve the stiffness of an element with the same geometry and from the same material. This is a useful rule, but the comparison must concern genuinely similar products. If you change the width, the depth of the profiling or the length, the result no longer follows from a single number. A fuller description is needed.

By |2026-11-15T19:34:36+01:002022-04-23|Building academy|Comments Off on Are thicker metal fence pickets always stiffer?

How to calculate the number of screws for sandwich panels without guessing?

There is no single correct number of screws per metre for every panel. Panel data, supports and loads are required. Only from the fixing design can the quantity for ordering be derived. An average per m² helps logistically but does not determine the layout. On walls and roofs, it is also important to distinguish between main fasteners and secondary connections. You can ask about a square metre of surface area, a linear metre of panel or a linear metre of joint. These are different bases for calculation. For a panel 1 m wide, the first two figures may be equal, but with a different module they are not. Always state the unit and the fixing scope.

By |2026-11-14T13:14:52+01:002022-04-19|Building academy|Comments Off on How to calculate the number of screws for sandwich panels without guessing?

What are the advantages and limitations of an insulated panel with a mineral wool core?

A mineral wool panel combines the casing and insulation in a single prefabricated element. It can be a good choice for specific fire requirements. However, it has a greater mass than many panels with a foam core and requires edge protection against water. A fair comparison should cover these characteristics together, without reducing the choice to a single slogan. Ready-made mineral wool panels can achieve reaction-to-fire class A2-s1,d0. This is a beneficial characteristic in many applications. However, it should not be used to replace the required fire resistance of a wall. The EI class relates to a specific assembly and duration for which defined functions are maintained. Installation, supports and connections remain part of the solution.

By |2026-11-14T10:54:55+01:002022-04-10|Building academy|Comments Off on What are the advantages and limitations of an insulated panel with a mineral wool core?

Six practical benefits of metal picket fences

Metal pickets allow you to build a visually light fence without the frequent renovation required by wood, but these benefits depend on correct design and installation. Before buying, assess whether the coating, posts and fixings suit the planned infill and operating conditions. Also check the gap between pickets, which affects transparency and wind exposure. Compare samples in daylight and view a test panel from different angles. Remember that coated steel does not need impregnation like wood, yet it does not mean a complete absence of maintenance.

By |2026-11-14T20:36:12+01:002022-04-09|Building academy|Comments Off on Six practical benefits of metal picket fences

How does a sandwich panel work and what should you know before building?

A sandwich panel combines several functions in a single element. Its core and facings work together, so they should not be assessed separately. The panel can form a wall or roof once fixed to a suitable structure. The connections also determine durability. This guide explains what you are actually buying and where the limits of the material itself lie. A typical panel has two facings bonded to a core. The steel surfaces and the material between them together carry loads. Adhesion at the interface between the layers is important. Delamination should therefore not be treated as a minor cosmetic defect.

By |2026-11-14T13:14:20+01:002022-04-05|Building academy|Comments Off on How does a sandwich panel work and what should you know before building?

What affects the working life of trapezoidal steel sheets?

In Poland, the service life of trapezoidal sheet depends not on a single parameter but on matching the material to the operating conditions. Check the steel thickness, the type of protection and the product's intended use in the specification, not just the profile symbol and colour. Beside a busy road, in an industrial environment or near the sea, the coating is selected for exposure, as it is for moisture and aggressive compounds inside a building. Installation quality, storage and later maintenance also matter. A warranty period alone does not predict service time, so compare the scope of protection and its limitations.

By |2026-11-14T17:10:10+01:002022-04-02|Building academy|Comments Off on What affects the working life of trapezoidal steel sheets?

What sets an insulated sandwich roof panel apart from other coverings?

A roof sandwich panel stands out because its metal facings and insulating core work together as a single element, not a loose set of layers. Before purchase, assess not only thickness but also load-bearing capacity, airtightness and fire requirements. Check whether the declared parameters refer to the whole panel, not just the core name. The shape of the outer profile and joints affects water drainage and stiffness. Core thickness alone does not determine a product's suitability.

By |2026-11-14T20:34:47+01:002022-03-30|Building academy|Comments Off on What sets an insulated sandwich roof panel apart from other coverings?

Starter profiles at the plinth: spotting defects at the foot of a wall

The lower edge of the wall cladding is where different materials and different tasks meet. The end of the cladding must be protected, water must be drained away and the continuity of seals must be maintained. Starter profiles bring order to this detail, but not every one of them carries the load of the panel. If there are streaks or gaps at the plinth, it is worth checking the whole assembly. Simply adding another trim may only hide the problem. Various cross-sections appear under the name starter profile. Some begin the installation of the cladding. Others cover the lower edge or form part of the connection to the plinth. Whether an element provides support is decided by the design. A thin masking trim does not become a load-bearing element merely because of its position.

By |2026-11-15T04:22:24+01:002022-03-25|Building academy|Comments Off on Starter profiles at the plinth: spotting defects at the foot of a wall

Inspecting a metal roof after the winter months

After winter, the key task on a metal roof is to establish whether there are signs of moisture and where they originate, rather than immediately tightening every screw. Assess the covering, flashings, gutters and equipment fixings from several sides in good light, using earlier photographs. Check for new stains in the attic, loose flashings, bent gutters and places where water changes direction. Note whether damp appears after rain, thaw or a frosty night — this helps diagnosis.

By |2026-11-14T20:35:31+01:002022-03-24|Building academy|Comments Off on Inspecting a metal roof after the winter months
Back to top