About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

Façade cladding with trapezoidal sheets: choosing between T18 and T35

When choosing trapezoidal sheet for a façade, first establish what the product is intended for, how it will be supported and what wind load will apply. T18 gives a finer pattern, while T35 emphasises the profiling more strongly, but appearance alone is not enough. Check the technical data sheet and cross-section to identify the decorative-coated side and the effective width. Remember the corners, openings and the bottom edge of the wall. Specify the wall application, as similar designations may conceal a different lap arrangement.

By |2026-11-14T20:36:48+01:002022-03-23|Building academy|Comments Off on Façade cladding with trapezoidal sheets: choosing between T18 and T35

T18 or T35 for a sheet metal roof: when does the profile matter?

T18 and T35 differ in profile height, but the comparison does not end there. Cover widths, steel thickness and the arrangement of supports matter. In a small building, fit to openings and edges is also relevant. A taller profile should be assessed as a complete solution, together with the structure, flashings and intended use. In the examples considered, T18 has a profile height of 18 mm and T35 — 35 mm. A deeper rib affects the geometry and stiffness of the section. However, it does not automatically mean that every T35 variant outperforms every T18 in all applications.

By |2026-11-14T17:09:32+01:002022-03-21|Building academy|Comments Off on T18 or T35 for a sheet metal roof: when does the profile matter?

Tile-effect roof coatings: how finishes differ and how to choose

A metal roof tile coating is not a single layer of paint but a system of metallic protection and organic layers that shields the steel and gives the covering its colour. When choosing, check whether the declared properties match the building's actual surroundings, including moisture, salt and pollution. Corrosion resistance, sunlight resistance, damage resistance and the scope of the warranty are key. Gloss or colour alone does not determine protection, so compare the data sheet of the specific product rather than an entire material family.

By |2026-11-14T20:37:26+01:002022-03-19|Building academy|Comments Off on Tile-effect roof coatings: how finishes differ and how to choose

Which benefits of sheet metal roofing matter for your building?

In Poland, a metal sheet roof is worth considering when the covering's low weight, variety of appearance and efficient installation suit the requirements of a specific building. Check not only the advantages of the sheet itself but also the load capacity of the existing roof structure, acoustic requirements and protection against moisture. Tile-profile sheeting, trapezoidal sheeting and sandwich panels serve different purposes, and the final assessment should cover all layers of the building envelope. Leave the choice of product to the designer, who will match weight, geometry and details to the building's conditions.

By |2026-11-14T17:11:40+01:002022-03-12|Building academy|Comments Off on Which benefits of sheet metal roofing matter for your building?

Which standing seam should you choose: single-locked, double-locked or click-fit?

A standing seam describes the way the sheet metal joint is formed. However, this name covers various solutions. A traditional seam locked on site is not the same as a factory-made click-fit panel. The differences affect the execution of details, thermal movement and the permissible pitch. The choice should not be reduced to the appearance of the vertical line on the roof slope. In traditional covering, the edges are appropriately profiled and locked into a joint. A double seam has an additional fold compared with a single seam. This changes the path that water would have to take. However, tightness also depends on the accuracy of execution, the substrate and the details used. The name alone is not a guarantee of a tight roof.

By |2026-11-14T10:54:07+01:002022-03-07|Building academy|Comments Off on Which standing seam should you choose: single-locked, double-locked or click-fit?

Matching tile-effect steel roofing to traditional and mountain-style houses

Choosing a metal roof tile for a traditional or mountain-style house starts with matching its profile and colour to the building's form, the timber, stone and wide eaves. Study the rhythm of the pressings on a sample positioned at an angle similar to the roof pitch, since a piece held upright in a shop casts different shadows from the finished covering. Leave the final choice of structure and fixings to the designer, who will account for local snow load and wind.

By |2026-11-14T20:36:09+01:002022-03-07|Building academy|Comments Off on Matching tile-effect steel roofing to traditional and mountain-style houses

What to check before installing a photovoltaic array on a metal roof

In Poland, photovoltaic panels can be installed on a metal roof, provided the mounting structure is matched to the specific covering and the load-bearing capacity of the entire roof is verified. Before deciding, it is worth establishing whether the documentation specifies the exact sheet model and thickness – without this, the assessment of fixing suitability may be uncertain. The condition, age and geometry of the roof should also be checked, along with how wind and snow loads are transferred to the building structure. If the covering needs repair, it is better done before installing the system.

By |2026-11-14T17:11:02+01:002022-02-21|Building academy|Comments Off on What to check before installing a photovoltaic array on a metal roof

The picket is the infill. What really holds the fence together?

On a finished fence, the pickets are the most visible part. They create the colour and rhythm of the entire fence. For this reason, it is easy to attribute to them tasks that are actually performed by other parts. In reality, steel pickets are usually the infill of a prepared structure. Understanding this difference helps when buying, renovating and assessing the contractor's work. It also helps avoid modifications based solely on appearance. Metal fence pickets define the gap and the character of the bay. They can have different widths, end shapes and finishes. Their profiling gives them the rigidity needed for their proper use. This does not, however, mean they can be used as arbitrary load-bearing elements. Every product has a defined purpose.

By |2026-11-15T19:35:07+01:002022-02-06|Building academy|Comments Off on The picket is the infill. What really holds the fence together?

How to choose an insulated wall panel with a mineral wool core for the actual building conditions?

The best panel with mineral wool is one that meets the requirements of the specific wall. For one building, fire resistance will be most important. For another, heating, appearance or the weight of the elements matter. Choosing the thickness alone does not settle the matter. You need to compare the whole panel, its fixing and the application conditions specified for the selected variant. Start with the building's function, the internal temperature and the nature of the work. A dry warehouse is assessed differently from a room that is regularly washed. Record the wall dimensions, openings and the expected panel layout. Determine whether the partition has fire and acoustic requirements. Only this information forms the basis for selection.

By |2026-11-14T10:54:43+01:002022-02-04|Building academy|Comments Off on How to choose an insulated wall panel with a mineral wool core for the actual building conditions?

How to estimate labour for installing sheet metal roofing

In Poland, the labour cost of laying sheet metal on a roof depends primarily on the roof's shape and the scope of work, not solely on the number of square metres of slope. Before comparing quotes, check whether the price covers substrate preparation, membrane, counter-battens and battens, or only the laying of sheets, and whether valleys, ridges, chimney flashings and gutter installation are priced separately. For a renovation, add removal of the old covering, protection of the building and waste disposal. Without this list, a rate per metre says little.

By |2026-11-14T17:11:18+01:002022-01-29|Building academy|Comments Off on How to estimate labour for installing sheet metal roofing
Back to top