Hipped roofs on a rectangular plan: how they work and when to use them

A hipped roof has four slopes, usually two trapezoidal and two triangular, which neatly close a simple house form. It is worth checking the actual roof drawing, because four similarly looking planes need not have the same dimensions or pitch angles. When ordering the covering, account for cuts at the corners, a complete set of flashings and the way moisture is drained from the roof layers. Watch out for the slopes at all external walls, which limit where tall furniture can stand. The choice depends on fit with the building form and residents' needs, not on assuming that four slopes mean simpler execution.

2026-11-15T00:23:19+01:00

How do you choose the thickness of a wall panel with mineral wool from 60 to 200 mm?

The 60–200 mm range offers several options, but it does not form a simple ladder from worse to better material. Thickness must be linked to temperature, fire requirements and construction. A thinner panel may suffice in one application, while a thicker one may be needed in another. First define the wall's task, then compare full variants. Determine whether the building will be heated continuously, periodically or not at all. Describe the humidity and the type of work inside. Check the fire and acoustic requirements. This requires panel spans, installation direction and an opening plan. None of this information is replaced by the floor area alone.

2026-11-14T10:55:29+01:00

When is T14 sufficient for cladding, and when is a higher profile needed?

T14 can look good on a small building. The low profile gives a calm wall pattern and does not dominate over the windows. On a roof, however, more than appearance decides the choice. The section, steel thickness, support and pitch must be checked. Below we show how to assess such a material without attributing to it the capabilities of the whole group of sheets. The number in the designation refers to the height of the corrugation. In the example variant, T14 is 14 mm. It does not describe the thickness of the steel sheet or the purlin spacing. Two similarly named profiles can have a different rib width, coverage and load table. Therefore the name from the offer alone is not enough to substitute one product for another.

2026-11-14T10:52:02+01:00

Installing trapezoidal steel roof sheets from the first sheet to the fixings

The key check before installing trapezoidal sheet is that the specific profile and roof design match, not the product name alone. The owner should verify whether the documentation states the sheet thickness, coating, sheet orientation and the required support spacing and fixing method. It is also worth establishing whether the façade version is approved for roof use. Only on that basis can the preparation of the slope and the sequence of work be assessed. The name T18 or T35 does not replace the data in the instructions, because the dimensions and properties of product families may differ.

2026-11-15T04:20:35+01:00

Is a board with a membrane enough? Utherm Sarking LE Plus in practice

In a roof with Utherm Sarking LE Plus, visible moisture can arise via more than one path. Run-off of precipitation and airtightness on the room side must be analysed separately. Understanding the function of the layers makes it easier to pinpoint the repair exactly where it is needed. Utherm Sarking LE Plus belongs to the PIR boards for pitched roofs. On both sides it has a multi-layer gas-tight laminate. The terms “polyurethane boards” and “polyurethane foam” are broader than the precise designation of the PIR product. When assessing the performance of the building envelope, it is worth checking the difference between Utherm Sarking LE and the LE Plus variant with an additional membrane. Before assessing the solution, the full name of the Sarking variant must be established before selecting additional membranes.

2026-11-16T03:17:43+01:00

How to sensibly insulate a garage, storage room and seasonal cottage?

A small building does not always need the same insulation as a heated house. A garage, storage room and summer cottage have different sources of moisture and different patterns of use. A cost-effective renovation starts with defining the objective. Only then are the material, thickness and scope of work chosen. The cheapest board does not have to give the cheapest result. Possible objectives are shorter heating-up times for the interior, reduced losses during operation or a more stable temperature. In an unheated storage room, insulation alone will not ensure a positive temperature throughout the winter. It slows down heat exchange but does not generate heat. If stored items must not freeze, heating must also be considered.

2026-11-14T10:55:50+01:00

Snow guards or snow fences for a pitched roof?

Begin by identifying which zones beneath the eaves need protection, then check whether the chosen arrangement suits the whole roof slope rather than just a fragment of it. The owner should verify the roof's pitch and length, the covering type, and the positions of entrances, walkways, cars and gutters. A linear snow fence limits the sliding of a larger mass of snow, while point snow guards can break it up and work alongside the other safeguards. Do not assume in advance that a single row will suffice — the selection depends on loads and slope geometry, not on eaves length alone.

2026-11-15T04:21:06+01:00

How to identify an existing roof covering before planning its replacement

An old corrugated roof may conceal more than one type of material. Individual sheets were replaced during successive renovations, and the names used by owners are often colloquial. New corrugated fibre cement sheets are not the same as old asbestos cement products. The term asbestos-free eternit describes a modern material, but it does not allow the composition of the existing roof slope to be assessed. Before planning replacement, information must be gathered without unnecessarily damaging the covering. The word "eternit" is sometimes applied to various corrugated sheets, regardless of their composition. The information that the roof was bought as asbestos-free may be valuable, but it is worth finding confirmation. Invoices, renovation descriptions, delivery notes and old photographs will be useful.

2026-11-15T19:36:17+01:00

Sizing roof rafters and setting their spacing

In Poland, the choice of rafter cross-section and spacing should follow structural calculations, not merely the roofing type or house width. The designer needs the span between supports, loads, timber class and structural scheme, as well as the permissible deflection and how connections are made. Check whether a span table matches your roof's assumptions: load type, support conditions and deflection limit. Lightweight metal sheeting reduces permanent weight but does not remove the effects of snow and wind. Leave the final selection to the designer, because a cross-section is not just an area but also a direction of bending and lateral support.

2026-11-14T17:09:40+01:00

Will mineral wool panels help reduce noise in a pavilion?

Mineral wool is often associated with quiet, but a ready-made sandwich panel has steel surfaces. Its sound insulation and its sound absorption are different properties. In a small pavilion, doors, openings and joints also determine the effect. Choosing the core alone is not enough to promise a specific level of quiet. Sound can pass through the wall, the joinery and gaps. It can also travel by flanking paths through the structure and adjacent partitions. If there is a large gate in the wall, its properties will be an important part of the result. A good panel will not automatically compensate for an open vent.

2026-11-14T10:56:22+01:00
Back to top