About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

Tracing the cause of a leak before arranging roof repairs

In Poland, a roof leak first requires rapid protection of the interior and identification of the cause, not merely hiding the stain. Readers should check whether water is reaching the electrical installation and secure items beneath the leak. A ceiling stain does not indicate the exact point of damage to the covering, so the inspection should cover the slope above and adjacent details such as chimneys, windows, valleys and service penetrations. Equally important is distinguishing a leak from condensation, which may call for a different solution than external sealing.

By |2026-11-14T17:10:30+01:002022-07-22|Building academy|Comments Off on Tracing the cause of a leak before arranging roof repairs

How do you match the thickness of a wall PIR panel to the indoor temperature?

Choosing the PIR thickness starts with the conditions of use. Temperature, heating duration and humidity matter. Next, the specific panel's parameter and the joints are checked. More millimetres usually restrict heat flow, but do not fix a leaky joint. A good choice also covers load-bearing capacity, coatings and fire requirements. Determine the target temperature and how long it is maintained. A small service point operating daily differs from a storage room heated occasionally. Frequent door opening and ventilation also matter. The panel requirements must be linked to the whole building's balance.

By |2026-11-14T13:14:54+01:002022-07-04|Building academy|Comments Off on How do you match the thickness of a wall PIR panel to the indoor temperature?

How do square gutters differ from traditional gutter profiles?

In Poland, choosing square gutters instead of traditional half-round ones requires the same attention as with half-round gutters: assessing performance, outlets and fixing method. The shape does not guarantee greater capacity, so before deciding it is worth checking the eaves cross-section, the layout of downpipes and the runoff zones from valleys and roof slope breaks. It should also be established whether the system will be visible, covered by a fascia or concealed, and components from a single manufacturer should be selected to avoid connection problems.

By |2026-11-14T17:11:25+01:002022-06-28|Building academy|Comments Off on How do square gutters differ from traditional gutter profiles?

Why do the same metal fence pickets age differently on two plots?

Two fences made from similar pickets can look different after years. This is not always due to a difference in quality. The surroundings, installation and maintenance all matter. Metal fence pickets are exposed to the ground, plants, roads and buildings. These conditions are worth describing before purchase. This allows the material to be chosen more sensibly than by comparing colour and sheet thickness alone. Water from dew, watering or condensation can settle on the surface. What matters is not only the presence of moisture but also the ability to dry out. A permanently sheltered and dirty location can behave differently from an exposed front. Inspections should therefore cover both sides and the lower part of the fence.

By |2026-11-15T19:35:10+01:002022-06-26|Building academy|Comments Off on Why do the same metal fence pickets age differently on two plots?

How to compare T18 and T35, sheet thickness and the cost of fleece?

T18 and T35 describe different profile heights, but they are not enough to select a covering. You need to check the drawing, steel thickness, supports and the intended use of the sheet. The price also depends on the coating and the coverage. Fleece can help limit condensation dripping, but it needs to dry out. It does not replace insulation or a tight roof. The profile affects stiffness and how the sheet performs. A taller trapezoidal profile may offer different possibilities under the same material conditions. However, this does not mean that every T35 is automatically suitable for any support spacing. Data for the specific product and loads are required.

By |2026-11-14T13:13:34+01:002022-06-23|Building academy|Comments Off on How to compare T18 and T35, sheet thickness and the cost of fleece?

How an eaves flashing directs rainwater into the gutter

The drip edge above the gutter is a flashing at the lower edge of the roof slope that helps direct water from the eaves into the gutter and protects the eaves zone. To assess its performance, trace the path of a droplet from higher up the slope to the outlet and check that each lap carries water onward rather than under the previous layer. Shape and position must suit the covering, membrane and ventilation. Simply sliding metal under the first sheet may not suffice, so the detail is matched to the roof layout.

By |2026-11-15T00:24:10+01:002022-06-23|Building academy|Comments Off on How an eaves flashing directs rainwater into the gutter

What is a panel with glass-fibre reinforced facing?

Some roof panels have a thin composite facing in place of the inner steel sheet. One example is glass-fibre-reinforced polyester resin, used in agricultural buildings. When choosing a panel, check the temperatures, moisture levels and cleaning agents it can withstand, as well as the joint details. The outer facing may be profiled steel. A rigid PUR or PIR foam core sits between this facing and the flat, glass-fibre-reinforced plastic surface facing the room. Together the layers form a sandwich panel. This construction differs from a simple translucent corrugated sheet.

By |2026-11-14T13:11:11+01:002022-06-22|Building academy|Comments Off on What is a panel with glass-fibre reinforced facing?

Tile-effect steel or concrete roof tiles for your home?

When deciding between metal roofing tiles and concrete tiles, start by assessing the structure and shape of the roof slopes, and only then compare appearance, the cost of the complete covering and ease of later repairs. The two materials differ in weight, element format and how details are finished. Metal roofing tiles are lightweight, which can be an advantage in a renovation when the truss has little load-bearing reserve. Looking at the roof is not enough – an inspection is necessary, checking cross-sections, connections and the condition of the timber. A heavier covering must be taken into account in the design of the entire load-bearing system.

By |2026-11-14T20:36:25+01:002022-06-17|Building academy|Comments Off on Tile-effect steel or concrete roof tiles for your home?

What zinc, magnesium and aluminium do in a metallic coating

Before comparing sheets, establish whether the metallic protection is meant to be visible or hidden beneath an organic coating — this affects how the product should be assessed. In a typical roof sheet, the zinc, aluminium and magnesium layer sits on the steel core, under successive finishing layers, though it may also form an uncoated surface. Check the exact coating designation, how its quantity is stated, and whether the data refer to one side or both combined. On a metal-tile sample you usually see the outer layer, not the steel's metallic protection itself.

By |2026-11-15T04:21:32+01:002022-06-17|Building academy|Comments Off on What zinc, magnesium and aluminium do in a metallic coating

Why does a metre of roof panel cost differently from a metre of wall panel?

Roof and wall perform under different conditions. They have different profiles, connections and loads. That is why their prices per metre should not be compared without describing the variant. Even an identical core and thickness do not make an identical product. A reliable quote separates panels, accessories and installation. It also lets you check what you are paying for in each part of the building. A roof panel must work with the slope and drainage system. Its outer skin usually has a pronounced trapezoidal profile. A wall panel may have a flat or lightly profiled surface. Connections are designed for a specific layout and fixing method.

By |2026-11-14T13:14:05+01:002022-06-13|Building academy|Comments Off on Why does a metre of roof panel cost differently from a metre of wall panel?
Back to top