About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

How to set out and fit modular tile-effect sheets on a sloping roof

The key to a successful installation of modular metal roofing tiles is to establish the batten spacing precisely from the instructions for the specific model, not from dimensions carried over from another profile. Before laying the sheets, check the geometry and condition of the substrate and plan the eaves details and water drainage. Also confirm that the covering suits the roof pitch. Differences in the pressing can prevent the module from being supported correctly, so verify the dimensions and fixing sequence for the chosen product before starting permanent fixing.

By |2026-11-15T04:21:19+01:002023-03-17|Building academy|Comments Off on How to set out and fit modular tile-effect sheets on a sloping roof

T8 on the façade: how to use a low profile without the waviness effect?

T8 has a delicate pattern and may suit soffits, gates or a small wall. However, a low profile does not hide errors in the substructure. On large areas, unevenness and movement of the sheet metal are easier to notice. It is worth starting with the scale of the surface and only then moving on to colour. Below we explain how to read the dimensions and where the limits of this material lie. The T8 designation usually refers to a low façade profile. In one variant, the height is 8 mm, the overall width is 1220 mm and the cover width is 1156 mm. Sheets are available in thicknesses of 0.5 or 0.7 mm. The recommended maximum length is 6 and 7 m respectively. This is an example product, not a common set of dimensions for the whole group.

By |2026-11-14T10:54:22+01:002023-03-13|Building academy|Comments Off on T8 on the façade: how to use a low profile without the waviness effect?

IKO enertherm KR ALU: assessing insulation beneath underfloor heating

Assessing the insulation under heating begins with establishing whether the uneven floor temperature results from the IKO enertherm KR ALU layer or from the pipe layout, the controls or the finish. The board alone does not determine the heat distribution. The proper reference point is the floor cross-section at the threshold between rooms and at the service penetration, with the layer thicknesses shown separately and the height from the substrate to the finished floor. Drawings and photographs taken before the screed was laid allow the actual pipe run to be reconstructed, which the print on the board does not document.

By |2026-11-16T03:17:30+01:002023-03-10|Building academy|Comments Off on IKO enertherm KR ALU: assessing insulation beneath underfloor heating

What must be maintained for a PIR roof to meet fire requirements during use?

The fire properties of the roof result from a specific arrangement of panels and joints. After acceptance, later openings, repairs and changes to equipment also matter. In a small building it is easy to treat these as minor works. However, every change should preserve the conditions on which the selection of the entire assembly was based. PIR describes the core material, but does not give the full classification of the panel. The facings, thickness and joint construction are important. Identification of the exact variant is needed. Data cannot be transferred from a similar product solely on the basis of the foam name.

By |2026-11-14T13:15:29+01:002023-03-09|Building academy|Comments Off on What must be maintained for a PIR roof to meet fire requirements during use?

Choosing a gutter system for sheet metal roofing

In Poland, gutters for a metal-sheet roof are selected primarily according to the roof geometry and the arrangement of outlets, not merely the type of sheet. Readers should check which part of the roof drains to a given gutter section, especially at valleys and with a complex building form. They should also examine the number and position of downpipes and the material compatibility of the system. Leave the choice of cross-section and shape to the designer, based on the specific system's data.

By |2026-11-14T17:11:37+01:002023-02-28|Building academy|Comments Off on Choosing a gutter system for sheet metal roofing

Modules or long sheets of tile-effect metal roofing: which suits your roof slope better?

A small module is easier to carry and to fit to a complex roof slope. A long sheet can efficiently cover a simple area. Neither solution wins on every building, however. You need to compare the cutting layout, delivery conditions and the requirements of the chosen profile. It also matters how a damaged section will be replaced later. A module has a fixed length and coverage width. Repeated elements form successive rows. Made-to-measure sheets are ordered in selected lengths, within the limits of the given technology. In both solutions, side joints remain. Long strips can reduce the number of transverse laps on a simple roof slope.

By |2026-11-14T10:54:09+01:002023-02-23|Building academy|Comments Off on Modules or long sheets of tile-effect metal roofing: which suits your roof slope better?

Does Eurofloor foil direct all the heat upwards? How it works

The question about the foil on Eurofloor is whether its surface alone directs heat towards the room. The board has a rigid PIR foam core and a multi-layer, gas-tight foil with a printed grid on both sides; the manufacturer intends it for thermal insulation of floors, including those with underfloor heating. Heat is retained primarily by the thermal resistance of the core, not by any reflection of radiation beneath the screed. Eurofloor must therefore be identified in the floor cross-section as a layer beneath the designed heating installation, and not as a mere screen on the surface.

By |2026-11-16T03:25:29+01:002023-02-15|Building academy|Comments Off on Does Eurofloor foil direct all the heat upwards? How it works

What should guide your choice of a tile-effect steel roof?

Before choosing a pattern or colour, establish which sheets the roof can take. The pitch and slope length, positions of windows and chimneys, and condition of the frame and substrate all affect the choice. On a refurbishment, compare the drawings with measurements on site. Include the diagonals and the edges where sheets will be trimmed. Use these dimensions to select the profile, coating and sheet format. For a fair price comparison, ask each supplier to include everything needed for your roof.

By |2026-11-15T04:21:17+01:002023-02-14|Building academy|Comments Off on What should guide your choice of a tile-effect steel roof?

When does an outlet insulated wall panel with a mineral wool core really pay off?

An outlet panel can lower the cost of a small enclosure, but a discount alone does not yet tell you whether the material suits the job. First you need to know why the grade was reduced. A scratch on the coating is a different problem from a damp core or a crushed interlock. It is also worth calculating how much of the purchased batch can be used without weakening the required wall properties. There is no single common list of defects for all outlet offers. The material may come from the end of a production run, a dimensional surplus or a batch with a visual deviation. It may also be damaged. The description should clearly distinguish these situations. The term “second grade” on its own specifies neither suitability nor the scope of documentation.

By |2026-11-14T10:54:39+01:002023-02-12|Building academy|Comments Off on When does an outlet insulated wall panel with a mineral wool core really pay off?

Barge flashings after a storm: which signs warrant a closer look?

After strong wind, a bent sheet corner is the easiest thing to notice. Less visible are disturbed fixings and gaps beneath the flashing. Barge flashings protect the side edges of the roof slope, so it is worth inspecting them during a roof check. Their good appearance from the ground does not yet confirm correct fixing. Conversely, a slight unevenness does not have to mean structural damage. The condition of the specific joint determines what to do next. From a safe position, check whether the barge flashing has kept a straight line. Look for raised ends, opened laps and sections standing away from the substrate. A photo taken from several sides is more useful than a close-up of the damage alone. It shows the position of the flashing relative to the covering.

By |2026-11-15T04:22:20+01:002023-02-02|Building academy|Comments Off on Barge flashings after a storm: which signs warrant a closer look?
Back to top