About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

Choosing trapezoidal steel sheets for a pavilion, shelter or small workshop

When choosing a trapezoidal profile, it is worth starting from the inside of the building. A dry shelter, a heated pavilion and a workshop with damp processes place different demands. Then comes the time for the profile, coating and cutting layout. This order helps match the material to everyday use, not just to the look of a colour sample. Determine whether the building will be heated and where moisture may come from. Wet tools, vehicles or the work performed change the conditions under the roofing. Sheet metal alone does not form an insulated building envelope. If insulation is needed, the entire layer build-up must be designed.

By |2026-11-14T17:09:16+01:002025-03-16|Building academy|Comments Off on Choosing trapezoidal steel sheets for a pavilion, shelter or small workshop

What installation errors lead to leaks and damage in panels?

Problems with the building envelope often begin with small decisions on site. An incorrect measurement, swarf or insufficient screw pressure can have consequences many months later. Inspection should therefore accompany installation, not appear only when a leak occurs. Below are the places where an error is easier to stop before the joint is covered. Crooked supports and incorrect spacings make correct panel bedding difficult. Tightening the sheet with a screw does not level the structure. It can instead deform the cladding or the interlock. Before work, verticals, horizontals and the position of components at openings must be measured.

By |2026-11-14T13:15:16+01:002025-03-14|Building academy|Comments Off on What installation errors lead to leaks and damage in panels?

Planning a steel machinery shed around the route farm vehicles take

The largest machine fits under the roof, but to drive it out you first have to move three others. This arrangement quickly becomes a nuisance in season. A steel hall for agricultural equipment should protect the machines and provide access to them. Floor area alone does not solve this task. When planning, working dimensions, the order in which equipment is used and the route from the stand to the gate all count. In the schedule, list the machines with the attachments that remain on them during storage. Allow for folded components, protruding mirrors and the highest points. A dimension from the catalogue may refer to different equipment. A steel hall needs clearance to allow safe manoeuvring. It is not worth designing the opening so that access requires exceptional precision every time.

By |2026-11-15T04:21:35+01:002025-03-06|Building academy|Comments Off on Planning a steel machinery shed around the route farm vehicles take

Rafter sizes and prices: what determines the timber specification?

Rafter dimensions are determined by structural calculations, not by a single universal table. Before purchase, check that the design accounts for span, timber type, support arrangement and the weight of the layers. The cross-section alone is not enough – connections and bearing points are equally important. Leave the sizing decision to the designer, who will assess load capacity and deflection. The price per metre of beam does not reflect the full cost of roof construction, so compare offers using a complete material specification and design.

By |2026-11-15T00:22:31+01:002025-03-05|Building academy|Comments Off on Rafter sizes and prices: what determines the timber specification?

What should you check on the technical data sheet for a photovoltaic roof element?

A technical data sheet lets you go beyond photos and general claims about a modern roof. But you need to know what to look for. Power, dimensions and weight describe only some of a product's properties. Installation conditions, the scope of testing and compatibility with the other system components are equally important. Before buying, compare the current data sheet with the installation instructions, the quote and the documents supplied for the specific order. Start with the variant name, model designation and date of the document. Similar-looking elements may differ in length, number of cells or connection method. A data sheet found in an old catalogue may not correspond to the current delivery. Ask the seller to confirm the designations for each item in the cost estimate.

By |2026-11-15T19:35:26+01:002025-02-20|Building academy|Comments Off on What should you check on the technical data sheet for a photovoltaic roof element?

Common roof shapes for detached homes and what sets them apart

The choice of roof shape is driven mainly by how the loft will be used and by the room layout, not by the appearance of the building alone. An owner should check whether the proposed geometry allows a sensible interior plan, accommodates the necessary windows and does not multiply unnecessary junctions. It is worth comparing two complete variants of the same house: the structure, roof layers, flashings, gutters and windows. A simpler layout usually makes execution easier, but durability depends on a correct design and careful details, so technical decisions should be left to the designer.

By |2026-11-15T04:20:30+01:002025-02-09|Building academy|Comments Off on Common roof shapes for detached homes and what sets them apart

What needs to be checked in a 100 mm mineral wool wall panel?

One hundred millimetres is a specific core dimension, but not yet a full wall specification. Panels with mineral wool of this thickness can differ in weight, insulation performance and joint. The choice should cover the entire variant and the installation method. Below we show how to assess 100 mm without treating this value as an automatic standard for every building. A 100 mm panel can have different mineral wool density and facing thicknesses. This affects weight and performance characteristics. The joint type can also differ. A variant with concealed fixing does not have to have the same U-value as a panel with visible screws. Do not combine the most favourable figures from several data sheets into one fictitious product.

By |2026-11-14T10:55:20+01:002025-02-04|Building academy|Comments Off on What needs to be checked in a 100 mm mineral wool wall panel?

Daylighting a loft with gable windows, roof windows or dormers

The way of lighting an attic should be matched to the room layout and roof shape, not chosen on the strength of one striking glazed area. It is worth checking where light needs to reach during the day, how partition walls are positioned and what obstacles lie outside. Gable windows, roof windows and dormers have different limitations, so before deciding you should draw the intended interior division and assess orientation and ease of operation. The solution should suit the future room layout, not only the state on the day of renovation.

By |2026-11-15T00:24:51+01:002025-02-01|Building academy|Comments Off on Daylighting a loft with gable windows, roof windows or dormers

Mono-pitch roofs: how they work, their advantages and their limits

A mono-pitch roof has a single slope falling in a chosen direction, which can simplify construction and reduce the number of details. However, it is worth checking whether the structure, pitch, drainage and covering are properly matched to the building's conditions. The connection to a higher wall is also crucial and requires particular attention. A simple shape does not mean a lack of details to design – there are still eaves, side edges and a top termination. The decision to use this layout should be based on an analysis of span, supports and structural material, not just on the simplicity of the form.

By |2026-11-14T20:37:58+01:002025-01-30|Building academy|Comments Off on Mono-pitch roofs: how they work, their advantages and their limits

Storing grain in a steel building: designing walls for grain pressure

Bulk grain does not only load the floor. It also exerts pressure on the surfaces that confine the heap. That is why an ordinary steel hall for machinery does not become a grain store simply by removing the equipment. A solution is needed that takes into account the method of storage and handling. Retaining walls, the floor, the fill height and the conditions for maintaining crop quality are particularly important. Sandwich panels and sheet metal protect the interior from the weather and carry the loads envisaged for the envelope. They must not automatically be assumed capable of taking up the pressure of grain. This also applies to the columns. The steel structure of the hall may not be designed for this type of loading. Filling the wall to a level that appears low does not solve the problem.

By |2026-11-15T04:21:37+01:002025-01-30|Building academy|Comments Off on Storing grain in a steel building: designing walls for grain pressure
Back to top