Choosing trapezoidal roofing sheet: when to consider T18 or T35

Start choosing trapezoidal roofing sheet by checking whether it suits the structure, roof pitch and service conditions. The names T18 and T35 indicate profile height, but they do not tell you everything about the sheet's parameters. Before buying, establish the steel thickness, coverage width, coating type, permissible loads and fixing method. The detailed geometry comes from the manufacturer's drawing, so similarly named sheets may differ in coverage width and load capacity. Also remember to distinguish the roof version from the façade version.

2026-11-15T00:23:54+01:00

Stock steel frames for farm buildings: checking the fit before ordering

When a farm needs a new covered space, the time needed to prepare the components matters. Our standard steel structures can be selected from available batches, without ordering every profile from scratch. The availability of a specific variant and the collection date are confirmed at the time of order. A steel hall still requires a prepared plot and a design matched to its function. A ready-made frame makes planning easier when it is known what it is to accommodate. Our duo-pitch structures cover widths of 8, 10, 12, 14, 16, 18 and 20 metres. A small variant may suit the storage of tools and selected machinery. A wider steel hall offers different options for arranging workstations and circulation. The choice should be driven by a layout with the actual equipment, not by the pursuit of the largest floor area alone.

2026-11-15T04:22:06+01:00

Roof flashings from eaves to ridge: choosing each component for its location

Metal flashings close the edges and junctions of a roof that cannot be finished with the covering alone. Rather than a generic recommendation, check the completeness of the order: whether every edge, valley, chimney and wall junction has a specific detail assigned. Take into account the roof geometry and the sheet profile. Bear in mind that flashings are not an optional extra to be omitted to reduce cost. Their role is to direct water and protect vulnerable points, especially where the roof slope changes direction and at elements projecting above the roof.

2026-11-14T20:36:44+01:00

Getting gutters ready for winter: what to check after cleaning

Vacuuming gutters removes leaves and sediment, but it does not replace an inspection of the whole drainage system. The owner should check whether, after cleaning, water flows freely from the roof surface through outlets, bends and downpipes to the receiver at ground level. A clean gutter does not guarantee flow if the fall is wrong or a joint is damaged. It is worth establishing which sections were actually checked rather than relying on outward appearance. The final assessment of how the system works is best made after the first heavy rain, watching for backflow or overflow.

2026-11-15T04:21:01+01:00

How should the anchoring of a steel hall be prepared for a concrete foundation?

The column-to-foundation connection transfers forces from the structure to the concrete. It is not selected solely on the basis of the weight of the panels. Bonded anchors can be part of the solution if they correspond to the design and the substrate. Geometry, hole preparation and curing conditions matter. There is no single set of diameters and depths for every hall. In addition to weight, wind, snow and other loads arising from the function of the building act on it. Tensile, shear and moment forces may occur at the column base. The base plate, anchors and concrete work together. Selecting a single rod without assessing this system is not a connection design.

2026-11-14T13:13:46+01:00

Matching the coating on metal roof tiles to the building’s surroundings

The choice of coating for a metal roof tile is determined above all by the environment in which the roof will operate, not by colour or guarantee length alone. An owner should check the material data sheet for the type of metallic protection, the organic layer, the core thickness and the permitted conditions of use. A farmer assessing an agricultural building must also consider interior humidity and whether the underside of the sheet will be visible. Only by comparing these details can one judge whether a given coating matches the actual demands.

2026-11-15T04:20:33+01:00

Which roofing membrane belongs where in the roof build-up?

The key is to establish whether the chosen membrane is to act as the underlay beneath the covering or as the layer on the room side – these roles are not interchangeable. The owner should check the intended use of the loft, the existing layers, the type of boarding and how moisture is drained away. During renovation, it is worth opening up the roof to determine what is actually beneath the covering, rather than relying on the colour of the old membrane. The designer decides the build-up, while selection rests on the scope of use and the documentation for the specific product.

2026-11-15T04:20:37+01:00

Does an integrated photovoltaic roof replace insulation?

A photovoltaic roof can replace part of the traditional covering while generating energy. This does not mean it takes over the task of thermal insulation. Warmth in winter and comfort in summer depend on the entire building envelope, including insulation, airtightness and protection against moisture. Integrating the cells organises the outer layer of the roof, but does not remove the need to design what lies beneath it. The covering primarily shields the building from the weather. In its active version it additionally produces electricity. Thermal insulation limits heat flow. The other layers can control the movement of water vapour, drain moisture and provide airtightness. A single shared term 'roof' does not mean a single material function.

2026-11-15T19:35:29+01:00

Planning a hipped roof: slopes, hips and supports

Whether a hipped roof performs correctly depends not on the shape of the solid alone, but on the truss layout and the arrangement of supports. It is worth checking that the design accounts for hip rafters, jack rafters and the points where loads are transferred to walls and internal supports. The roofing plan should indicate sheet cutting, ridge flashings and ventilation. The cost estimate should itemise these details separately. At handover, the geometry of the corners, the support and fixings are checked, along with the quality of cuts and the patency of ventilation.

2026-11-15T00:23:04+01:00

Does hail mean the entire photovoltaic roof must be replaced?

After a hailstorm, you should assume neither that the roof is fully functional nor that it needs to be completely replaced. The outcome depends on the event, the construction of the covering and the actual damage. With an integrated roof, you need to assess watertightness, the condition of the active layer and how the installation is performing. Product hail testing is important information, but it does not guarantee resistance to every possible weather event. Testing is carried out under defined conditions. The size and speed of the impacting objects, the number of impacts and the criteria for assessing the sample all matter. The phrase 'hail-resistant' on its own is therefore incomplete. Ask for the document, the method and the product version. Do not compare different results on the basis of a single highest figure.

2026-11-15T19:35:43+01:00
Back to top