Choose a material

Roofing sheets

Blachy trapezowe — ilustracja kategorii

Sandwich panels

Płyty warstwowe — ilustracja kategorii

PIR insulation boards

Płyta izolacyjna PIR z cienką folią — ilustracja kategorii

XPS

Płyty XPS — ilustracja kategorii

Accessories

Wkręty i łączniki — ilustracja kategorii

Fencing

Sztachety metalowe — ilustracja kategorii

XPS insulation

XPS under a terrace on pedestals. What determines the pressure?

At a glance

Terrace slabs on pedestals create a convenient space above the roof. However, high pressures can occur under their small bases. That is why XPS under such a terrace is selected taking into account the entire load transfer path. Extruded polystyrene is a rigid thermal insulation, but not every type of it will be suitable. The term styrodur is sometimes used colloquially, but the project requires precise identification of the boards. The force from a terrace slab is transferred to several pedestals and then to the roof layers. The area of the terrace itself therefore does not yet indicate what pressure the XPS will experience. The number of supports, their spacing, the size of the bases and the way they are laid must be known.

Three yellow XPS boards placed side by side with visible differences in thickness

From the weight of the floor finish down to the substrate

The loads assumed for use of the terrace also matter.

A system with an additional load-distributing layer behaves differently from a pedestal resting directly on the insulation. These variants must not be swapped during installation. Extruded polystyrene should receive the load in the manner provided for in the calculations and permitted for the entire solution.

The advantage of rigid boards is the possibility of achieving an even thermal insulation layer of a defined thickness. Easy cutting helps to fit it to the edge of the terrace. With proper support, this creates a clear basis for further work.

Why is the average per square metre misleading?

The weight divided by the terrace area gives only an average value. Under the foot of a pedestal, the pressure can be considerably greater. At corners and edges, different support conditions apply. Also, if one element is damaged or poorly levelled, the load may be distributed unevenly.

Selecting XPS therefore requires a local analysis, not merely adding up masses. Support should not be assessed on the basis that the board does not bend under a boot. Such a test does not describe the material’s behaviour over many years. XPS may appear hard and yet still require a larger area over which the pressure is distributed.

CS and creep are different pieces of information

The CS designation provides information about behaviour during a specific compression test. It is not directly the permissible pressure of a pedestal. For permanent loading, creep and the permissible deformation of the system must be taken into account. A slight displacement of the substrate may be visible as an uneven surface.

Extruded polystyrene should be selected so that its behaviour does not interfere with the function of adjacent layers. The manufacturers of XPS include PNP, FIBRAN and Finnfoam. Their documents describe various board variants. The comparison should cover specific declarations, not solely the number visible in the name of the material offered.

Waterproofing also requires protection

In an inverted roof, the XPS layer is located above the waterproofing. However, additional materials occur between the surface and the ceiling, and their arrangement must be preserved. The support foot must not damage the covering or cut through protective layers. The correct pads and support result from the adopted system.

Not every flexible interlayer performs a load-distribution function. A thin protective element can protect against friction but only weakly change the pressure on the XPS. These roles must be separated. Selecting a material solely on the basis of its softness or thickness is insufficient.

Maintain the water drainage path

Rain penetrates through the gaps between the terrace slabs. Water should drain away from the appropriate roof levels without blocking the flow through the supports and additional pads. XPS does not form a watertight basin. The design includes slopes, outlets and access for cleaning them.

Extruded polystyrene has low water absorption, but this does not exempt one from assessing the moisture of the entire building component. During installation, waste that could clog the drain must be removed. Supports placed close to the outlet must not hinder servicing. It is worth providing an easily removable section of the surface above the inspection points.

The terrace level is determined before ordering

The final height is made up of the slopes, waterproofing, XPS, protective layers, supports and the surface finish. The reserve at the door threshold is often limited. It should not be recovered by arbitrarily reducing the thickness of the thermal insulation. This requires the roof parameters to be checked again.

Similarly, the height of the upstands and the detail of the parapet should be assessed. A greater XPS thickness helps thermally, but changes the geometry of the details. It is best to prepare sections through the door, the terrace edge and the outlet. Only such a complete set allows you to establish whether all the layers will actually fit.

Do not base acceptance on a short test

Setting up a few supports and stepping onto the terrace board may reveal that it wobbles, but it does not replace calculations. Such a check takes a moment and does not reproduce the permanent load or the varying roof conditions. If the base visibly sinks, the cause must be clarified before further installation. Adding a piece of XPS under one support changes the bearing and is not a neutral correction. The evenness of the surface finish must be achieved within the solution for which the parameters of all layers have been established.

What should be checked on a finished terrace?

The inspection should cover the stability of the surface finish, the levels and the conformity of the bearing with the design. Before covering the XPS, it is worth documenting the spacing of the supports and the load-distributing layers that have been installed. A photo of the finished floor alone will not show these elements.

Heavy planters or built structures should not subsequently be placed in random locations. The new load may require additional support or a change of layout. A well-designed terrace makes use of XPS’s resistance to pressure and moisture while at the same time leaving the possibility of checking the drainage and replacing individual paving slabs.

7 branches. Materials closer to your project.

Izoprofil.org map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E
  • BŁONIE — ul. Sochaczewska 138A
  • RADOM — ul. Grobickiego 8
  • ŁÓDŹ — Natolin 8
  • OLSZTYN — Barczewo, ul. Prosta 9
  • WROCŁAW — ul. Jerzmanowska 10C
  • GORZÓW WLKP. — ul. Zielona 33/34

Check prices and availability: +48 500 409 109

Free quote