PIR insulation
Utherm Roof LE: why a good lambda value is not enough for a roof
At a glance
A cooler zone at the parapet does not yet tell you whether the problem concerns Utherm Roof LE. The termination of the insulation layer or air flow through a leak may be significant. When assessing a roof, it is worth separating the properties of the board from the condition of the details executed on site. Utherm Roof LE is a PIR board intended for flat roofs and roofs with a low pitch. The core is covered on both sides by a multi-layer, gas-tight laminate. The terms “polyurethane boards” and “polyurethane foam” are broader than the precise designation of the PIR product. When assessing the performance of the building envelope, it is worth checking the limited insulation height at the roof parapet with Utherm Roof LE. Before assessing the solution, the thickness of Roof LE, the taper and the remaining roof layers must be added together.

Utherm Roof LE boards where roof height is restricted
It is easy to confuse the functions of the components if one disregards the fact that the gas-tight laminate does not determine the height of the remaining layers of the roof build-up. A correct diagnosis should allow the low lambda to be used without shortening the required termination of the covering. During the inspection, compare the dimensioned cross-section at the lowest and highest point of the system with the information on how it was executed.
Lambda and the thermal resistance of a specific thickness
Lambda 0.022 W/(m·K) alone describes the material, not the whole roof. Only relating it to a specific thickness shows how much resistance the board contributes: for Utherm Roof LE 100 mm the declared R_D is 4.50 m²K/W. When diagnosing an existing roof build-up, check whether this is the thickness actually installed on site and whether the result refers to the board and not to the assembly.
For a correct interpretation, the resistance of the Roof LE board must be separated from the U-value of the entire roof build-up. A similar notation does not have to mean the same thing, because the fastenings and the connection to the parapet participate in heat flow outside the regular field. Such a distinction allows variants to be compared for the same thermal task and height limitation. Before drawing a conclusion, ask for the catalogue thickness together with the calculation result for the entire assembly, so that the figures refer to the actual layer.
Polyurethane insulation at openings and edges
The assessment of the substrate and the distribution of joints is part of establishing the execution, not of describing the board itself. Roof LE requires support on a substrate intended for the given roof, and the joints are planned so that successive rows do not form long, continuous gaps. Inspection of the board layout at the rooflight row and at service penetrations shows whether this condition has been maintained.
When planning and assessing the installation, it is worth drawing out the joints and cut-outs at the bases of elements penetrating the roof. The installation rules must be checked separately, because a large board will not automatically reduce waste on a surface with numerous openings. Establishing the cause should make it possible to maintain continuity of the thermal insulation without assembling the edges from random narrow strips. When assessing polyurethane insulation, check the laying plan with the chosen format and the marking of the joints at the openings before accepting the completed joint.
Utherm Roof LE laminate and compatible covering
Critical points on the roof are outlets, skylights, parapets and service penetrations. The board thickness is linked here to the height of the waterproofing upstand and to the falls, which is why the junction of the aluminium-laminated Roof LE with the intended covering must be examined in section, not only at the surface.
Before a repair is specified, the interaction of the adhesive or fixing with the Roof LE facing must be confirmed. No conclusions should be drawn from appearance alone, because a similar appearance of silver facings does not prove equal adhesion of the materials. The information gathered should make it possible to choose a system that maintains the waterproofing and thermal insulation in accordance with the documentation. Before specifying the repair method, check the accessory set and the method of preparing the contact surfaces, as well as the history of previous work.
Compression and requirements for the entire roof covering
A CS value of at least 150 kPa at 10% deformation describes the behaviour of Utherm Roof LE under the declared conditions, not the load-bearing capacity of the roof under any permanent load. The pressure of a device on a small foot is a separate issue from the board itself. Therefore, in the documentation, the material parameter must be distinguished from the way forces are transferred through the Roof LE system.
When reading the scope of the declaration, you must check the duration of the pressure and the way the forces are distributed above the insulation. Too far-reaching a conclusion would be unjustified, since the test point at 10% deformation is not an approval for any permanent pressure. The explanation should allow the support to be selected without converting a single figure into the load-bearing capacity of the whole roof. In case of doubt, you must check the geometry of the support, the construction of the protective layers and the separate fire classification of the system, instead of settling for a general assurance of quality.
Polyurethane insulation: format, delivery and roof cost
The order should identify the product by the full name Roof LE, thickness, format and edge finish, since the name alone does not specify the delivery variant. The catalogue lists, among others, the formats 1200 × 600 mm and 2400 × 1200 mm. When assessing an offer or accepting works, the difference between them concerns above all logistics: a larger sheet is handled and cut differently.
Before assessing quality or price, it is worth matching the size of the Roof LE board to access and the planned cutting layout. Without this, the result is difficult to compare, since the largest format may require additional space for handling and cutting. Identifying the scope should allow the number of operations to be reduced while maintaining correct joints and terminations. Base your conclusion on costs or quality on data covering the quantity survey of full boards, cut pieces and materials needed at the roof perimeter.
A case worth considering
When a cooler strip appears at the parapet, you should not immediately regard the lambda of Roof LE as the cause. You must establish how the horizontal insulation ends and whether it connects with the vertical thermal insulation. Air flow through leaks may also be significant. It is worth comparing the visual inspection with the documentation before covering. The repair should correspond to the established mechanism, instead of relying solely on adding thicker boards in the field.
7 branches. Materials closer to your project.
- SEROCK — Dzierżenin 34 E
- BŁONIE — ul. Sochaczewska 138A
- RADOM — ul. Grobickiego 8
- ŁÓDŹ — Natolin 8
- OLSZTYN — Barczewo, ul. Prosta 9
- WROCŁAW — ul. Jerzmanowska 10C
- GORZÓW WLKP. — ul. Zielona 33/34








