Choose a material

Roofing sheets

Blachy trapezowe — ilustracja kategorii

Sandwich panels

Płyty warstwowe — ilustracja kategorii

PIR insulation boards

Płyta izolacyjna PIR z cienką folią — ilustracja kategorii

XPS

Płyty XPS — ilustracja kategorii

Accessories

Wkręty i łączniki — ilustracja kategorii

Fencing

Sztachety metalowe — ilustracja kategorii

PIR insulation

BauderPIR FA-TE: identifying the edge profile and correct variant

At a glance

A local unevenness in the surface of a terrace with BauderPIR FA-TE requires establishing whether its source is the support and the pressure of the pedestals, the layers above the insulation, or the material itself. Identification begins with naming the observed symptom and the conditions in which it arose, not with an assessment of the quality of the PIR. With this product, the key place for inspection is the threshold of the terrace door and the nearby drain, where the distance between the substrate and the permissible surface level is checked. The reference point is the terrace cross-section at the door with marked levels, allowing the symptom to be related to the intended layer build-up.

Grey fine-grid facing on a pale core, accompanying the BauderPIR FA-TE guide

First, the question of the cause

A comparison of the as-built condition with a section drawing through the terrace doorway showing the levels shows whether the planned layer build-up accommodated the insulation, drainage and finishing layers. On this basis, a property of BauderPIR FA-TE is distinguished from a joint defect, instead of attributing the unevenness to the board.

The correct product and the scope of its data

When checking a BauderPIR FA-TE order, the data for the whole board must be separated from the description of its core. Aluminium facings, λD 0.022 W/(m·K), CS(10/Y)120 and fire reaction E are declared, and the external dimension is 1200 × 600 mm. The British documentation states straight edges, whereas the Polish data sheet gives a fitting dimension of 1185 × 585 mm; the designation FA TE F with a rebated edge also appears. The delivery variant is not determined by comparing these records without confirmation. The term “polyurethane boards” does not replace the full name when verifying an order, and the PIR foam is a core that must not be equated with the properties of the complete board.

How to read a simple example

For BauderPIR FA-TE, first identify the edge and the actual fitting dimension, then the thickness. For 80 and 100 mm and λD 0.022 W/(m·K), the calculation gives approximately 3.64 and 4.55 m²K/W respectively. The difference helps to check for a mistake in the variant designation, but it does not determine the source of cold or moisture at the terrace threshold. The threshold and the adjacent drain require their own inspection.

The example with BauderPIR FA-TE concerns the height limit below the threshold with the required finish, not every terrace defect. The external format of 1200 × 600 mm alone does not indicate the cause of the symptom. At this point, the height of the surface, insulation and drain is brought together on a single cross-section; a document confirming the edge and fitting dimension of the delivery serves as comparative material. Where the data deviate from reality, the description of BauderPIR FA-TE and the condition of the layers are corrected first.

Matching the action to the identified problem

The thickness of the thermal layer affects a different range than correcting the remaining terrace heights. In BauderPIR FA-TE, a distinction must be made between what results from the observed symptom and what results from the layer build-up. The terrace doorway threshold and the adjacent drain are assessed differently from the remaining surface. Separately, the data of the square-edged UK variant must be compared with the Polish data sheet with the smaller coverage dimensions. The decision is made by the designer of the terrace and the connection to the door, who knows the requirements of the entire cross-section; on this basis, the description of FA-TE with a specific edge variant serves for repair or a new order.

What can be seen at the joint

The inspection of BauderPIR FA-TE is to confirm that the edge profile matches the documentation and the delivery. The condition of the aluminium facing with the printed guide grid in the variant described is recorded separately: a different print or colour does not prove an open joint, loss of facing or permanent deformation. The reference is the document confirming the edge and the fitting dimension of the delivery. On the other side lies or is to lie the terrace finish with waterproofing and surfacing, which may hinder access to the damage. In the note, record whether the inspection covered the terrace doorway threshold and the drain beside it, or whether this was only inferred from the adjacent surface.

How to separate a feature from a defect

The loads of the terrace surfacing and its supports must be distributed in accordance with the adopted build-up above BauderPIR FA-TE. The height below the door threshold must not be used by the insulation at the expense of the other required layers. Measure the levels at the door and the drain so that the designer can assess both the load and the space available for repair.

The conclusion should have limits

Attach the FA-TE delivery document specifying the edge and cover width to the terrace repair description. On the cross-section at the door, compare the level of the surfacing, insulation and drain, marking the areas inspected directly and the further openings required. Such a complete set of data allows a decision to be made as to whether the insulation thickness, the drainage or the finish needs to be changed.

7 branches. Materials closer to your project.

Izoprofil.org map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E
  • BŁONIE — ul. Sochaczewska 138A
  • RADOM — ul. Grobickiego 8
  • ŁÓDŹ — Natolin 8
  • OLSZTYN — Barczewo, ul. Prosta 9
  • WROCŁAW — ul. Jerzmanowska 10C
  • GORZÓW WLKP. — ul. Zielona 33/34

Check prices and availability: +48 500 409 109

Free quote