Polystyrene and thermal insulation
Does an unheated basement change the way a house is insulated?
At a glance
An unheated basement can remain outside the heated part of the house. In that case, the floor structure over the basement becomes an important separating layer, not just the basement wall. However, the junctions at walls, stairs and services must be resolved. The decision depends on how the basement is used, on moisture and on the available height. One single scheme does not suit all buildings. A storage room, a garage and a future workshop are different scenarios. If the basement is to remain cool, the heated ground floor should be separated from it by a suitable separating layer. If you plan to heat the entire basement later, it is worth taking this into account already during the renovation. Carrying out the finishing and services twice can make a change of use more difficult.

First establish the function of the basement
The boundary of the heated part of the building does not have to coincide with ground level. It should form a continuous system of building components. In addition to the ceiling, it includes the door by the stairs and the walls separating spaces at different temperatures. With an open stairwell, warm air can be exchanged between storeys despite careful thermal insulation of the basement ceiling.
Thermal insulation of the ceiling from below
Insulation beneath the ceiling slab limits its cooling from the basement side. It allows the floor level on the ground floor to be retained, but reduces the height of the underground rooms. The routing of pipes, luminaires and doors and access to valves must be checked. Areas requiring servicing and components whose condition must be checked periodically should not be covered.
EPS can only be considered in a system intended for such an application. The method of fixing, the finish and the fire requirements relate to the entire assembly. The reaction-to-fire class of the board alone does not describe the safety of the ceiling. A material intended for use under a screed does not automatically become suitable for bonding to the underside of a ceiling slab without protective layers.
Thermal insulation from the dwelling side
In the case of a general renovation of the ground floor, insulation above the ceiling slab can be considered. The boards, the screed and the finish must then fit within the available height. Thresholds, stairs, balcony doors and the load-bearing capacity of the ceiling slab are significant. Raising the floor by even a few centimetres can necessitate changes in adjacent rooms and at entrances.
The selection of EPS covers thermal and mechanical properties. CS(10) must not be equated with a permissible permanent load. If the screed is also to reduce impact sound, an acoustic analysis is required. A rigid thermal insulation board and resilient EPS T have different functions. The layer thicknesses must be selected as a complete floor assembly.
What happens at the walls and stairs?
The floor slab rests on walls that can conduct heat to the cool basement. This creates locations that require a separate detail. Insulating the floor slab field alone does not eliminate all linear thermal bridges. It is particularly worth inspecting the edges, the beams and the internal walls passing through the boundary of the heated part of the house.
At the stairs, the airtightness and insulating performance of the closure matter if it is to separate two zones. The doors should match the intended function, and the penetrations of services should be sealed with suitable materials. However, the required ventilation must not be closed off arbitrarily. The separation of thermal zones must be compatible with the operation of the equipment and the air exchange.
Can the basement walls be omitted?
Even an unheated basement requires protection against water and damage. Insulating its walls may be justified to limit the cooling of the floor slab edge or for other design purposes. This does not mean that all surfaces must be insulated equally. The scope is determined after assessing the building components and the temperatures we want to maintain.
The basement may contain water pipes, storage tanks and equipment with specific temperature requirements. After cutting off the heat supply from the ground floor, the conditions there may change. Protection of the installations must be planned, as well as the way moisture is controlled. Thermal insulation alone does not replace the repair of leaks or proper ventilation of the rooms.
How can the renovation variants be compared?
The comparison should cover the cost of the entire system, the loss of height and the difficulty of executing the details. Lambda describes the material, while Uc relates to the building component. A layer with a lower lambda can be helpful when there is little space, but it must meet the requirements specific to the application. A low price for the EPS alone does not determine the cost of rebuilding the floor or ceiling.
It is worth preparing a section through the ceiling with the perimeter edge and the staircase. On that basis it is easier to identify what should remain in the warm zone. Before choosing a variant, existing dampness must also be identified. Sealing a wet substrate with new layers can hinder drying and conceal damage instead of improving comfort on the ground floor.
Well-known EPS manufacturers include Termo Organika, Austrotherm, Ekobud and Dom-Styr. The intended use of the boards must be checked separately for the ceiling and the floor.
7 branches. Materials closer to your project.
- SEROCK — Dzierżenin 34 E
- BŁONIE — ul. Sochaczewska 138A
- RADOM — ul. Grobickiego 8
- ŁÓDŹ — Natolin 8
- OLSZTYN — Barczewo, ul. Prosta 9
- WROCŁAW — ul. Jerzmanowska 10C
- GORZÓW WLKP. — ul. Zielona 33/34








