PIR insulation
BauderPIR M/MF: the mineral facing and PIR foam core
At a glance
The answer to the question of the difference between BauderPIR M/MF and a mineral wool board lies in the construction of the product: the matt mineral fleece is a facing on both sides, while the core is still PIR foam. The assessment of an existing roof must therefore start from the product designation, not from the appearance of the top surface. During an inspection of BauderPIR M/MF, it must be established whether the correct thickness has been retained beneath the waterproofing and whether the substrate and installation conditions correspond to the assumed system. The reference point is the documentation for the specific M or MF thickness together with the description of the connection to the covering.

First, the question of the cause
Comparing the exposed area with the detail drawing should show whether the correct lambda value and a compatible junction with the roof covering were specified for the M/MF variant. This separates an error in selecting the parameter from a defect in the completed joint.
The product itself and the scope of its data
In BauderPIR M/MF the product consists of a PIR core enclosed on both sides by mineral fleece, not just a matt top surface. The family comes in a format of 1200 × 600 mm, whereby M and MF differ in the edge profile. For variant M, the Polish data sheet states λD 0.026 W/(m·K) in the range from 80 mm to below 120 mm, so a constant lambda of 0.022 should not be assumed. The documentation lists at least 120 kPa in the compression test and fire reaction class E. When checking an order, the full name BauderPIR M/MF is needed, because generic “polyurethane boards” indicate neither the facing nor the edge; after all, the properties of the complete board also include the facings, not only the core.
How to read a simple example
In the variants under consideration, BauderPIR M/MF with lambda 0.026 W/(m·K) gives a simplified resistance of about 3.08 for 80 mm and about 3.85 m²K/W for 100 mm. The calculation does not assess the adhesion of the waterproofing. If the problem concerns the connection, the type of fleece, the condition of both surfaces and the edge profile must be established; if it concerns thermal insulation performance, the actual thickness must also be confirmed.
The numerical example for BauderPIR M/MF shows that a change in thickness gives a different resistance, so misidentifying the variant may explain part of the discrepancy, but it does not indicate the cause of the defect. Before drawing a conclusion, the thickness range in the document for the ordered variant must be read and compared with the description of the fleece on both surfaces and the edge profile. In the event of a discrepancy, the description of the product and the layer build-up is corrected first.
Matching the action to the identified problem
Preserving the designed facing and selecting the thickness is a different task from rebuilding the arrangement confirmed after re-comparison. In BauderPIR M/MF, each action is attributed to an identified symptom, and the area of the fleece under the waterproofing is assessed separately from the rest of the field. It is a mistake to calculate the board with the mineral facing using the lambda of the aluminium variant. When doubts concern the entire cross-section, the data are assessed by a specialist approving the conformity of the insulation with the covering; then the schedule of thicknesses, facings and edges justifies repair or a new order.
What can be seen at the joint
During the inspection of BauderPIR M/MF, check the edge profile — straight in M, rebated in MF — and the condition of the matt mineral fleece on both surfaces. A different print or shade does not indicate a defect; an open gap, loss of facing or permanent deformation require clarification. Waterproofing compatible with the mineral facing makes access to the damage difficult, so record whether the inspection covered the fleece beneath it or only inferred from the adjacent section.
How to distinguish a feature from a defect
When repairing BauderPIR M/MF, assess the evenness of the substrate and the behaviour of the fleece under the waterproofing. In addition to the thickness, the conformity of the mineral facing with the intended covering is important. The specialist approving the material set should receive the documents for the M or MF variant and a record of the condition of the exposed joint.
The conclusion should have limits
Select the replacement material according to the thickness range specific to M or MF, the type of fleece and the edge profile. The inspection report should indicate which section under the waterproofing could be exposed and where the conformity of the joint remains unconfirmed. Supplementing these data precedes ordering boards with the correct lambda and facing.
7 branches. Materials closer to your project.
- SEROCK — Dzierżenin 34 E
- BŁONIE — ul. Sochaczewska 138A
- RADOM — ul. Grobickiego 8
- ŁÓDŹ — Natolin 8
- OLSZTYN — Barczewo, ul. Prosta 9
- WROCŁAW — ul. Jerzmanowska 10C
- GORZÓW WLKP. — ul. Zielona 33/34



